1. Adjustable Belt Tensioner/Tightener and Belt Tie (Tevo Tarantula)
https://www.thingiverse.com/thing:1780636
Adjustable Belt Tensioner/Tightener and Belt Tie (Tevo Tarantula) by supasorn
Update 11/5/18: Added 1.5mm base to the thick version.Update 11/4/18: Added a thick version (+2mm thickness).Update 3/11/17 : New hole, added fillet.Update 10/23/16 : increased thickness for screw holder and legs. A simple, adjustable belt tensioner + a be
www.thingiverse.com
원래 제품에 스프링형태의 텐셔너가 들어있는 것 같으나... 중고구매시 받지 못함....
설마 이 헐렁함을 가지고 지금 잘쓰고 있었다고 말할수 있을까 싶음...
그냥 이거 프린트 해서 사용함... 다른 프린터에도 활용가능!!!
최고임!
2.Part Cooling Nozzle for Anycubic Kossel
https://www.thingiverse.com/thing:2671635
Part Cooling Nozzle for Anycubic Kossel by GER776
UPDATE 2018-04-25: Added Fusion360 file. UPDATE 2018-01-11: Added _RevA. Came across the problem that the hotend had difficulties reaching and keeping very high temperatures as the original nozzle seems to cool the hotend as well. Probably related to the c
www.thingiverse.com
역시나 나는 블로우 팬덕트를 너무 사랑하는 것 같다.
현재는 아래 블로우 팬덕트를 프린트 중 ㅋ
https://www.thingiverse.com/thing:2347503
ANYCUBIC Kossel Delta Double Points Filament Cooler by Facocero
Hello Firiends, this is another review of the Cooling Duct for Anycubic printers, this time with double output, for efficient cooling of the filament during printing Are welcome comments and photos of your prints thanks ;-) V1.2: Some improvements and incr
www.thingiverse.com
그새 교체...
이게 좀더 좋은듯... 일단 열에의한 변형이 적음.
3.Tower Endcap... 확실히 보기 좋음 그리고... 그쪽으로 먼지가 덜 들어가서 프린터에게도 좋을거라고 생각하기로 함. ㅋ
https://www.thingiverse.com/thing:1969059
Anycubic Kossel Linear Delta Tower Endcap by peaberry
Snap on end caps which fit the top of each tower on the "Anycubic Kossel Linear" printer. Intended to stop dust collecting, and to cover the limit switch wiring and idler wheels. The printer has 2020 extrusions, and the caps may fit other similar Kossel De
www.thingiverse.com
4.Rod Damper... 안정감을 주는 것 같긴 한데 자꾸 빠짐... 다른걸 찾아봐야 할듯...
https://www.thingiverse.com/thing:2105393
Kossel Delta Linear Rod Damper by mrchilton
I designed some dampeners to span my linear rods on my Anycubic Kossel plus to dampen the vibrations. The rods were "clicking" during fast movements. The dampeners clip onto the parallel rods to put a slight amount of tension between them and eliminate the
www.thingiverse.com
5.Control Knob... 아.... 빈약한 노브 안녕~~~^^;
https://www.thingiverse.com/thing:2868497
Anycubic Kossel Control Knob (Revised) by Corn_Flake
The same control knob as the original from UEPONYA. I knocked off some of the sharpness on the knurling, smooth out the edge around the round dimple on the face of the knob. Print this model with open-side down. Support is not always necessary if the print
www.thingiverse.com
'3D PRINTER > ANYCUBIC Linear Delta' 카테고리의 다른 글
| ANYCUBIC LINEAR DELTA의 AUTO LEVELING 사용하기... (2) | 2019.08.04 |
|---|---|
| ANYCUBIC LINEAR DELTA의 CURA를 이용한 펌웨어 업그레이드/원복... (0) | 2019.08.04 |
| Anycubic Kossel Linear Delta... 영입!!! USB DRIVER설치 및 CURA SETTING...20190804 추가수정... (2) | 2019.07.30 |
댓글