ENDER 5를 조립하기 전에 뽑아두면 좋은 것들 입니다.
조립한 다음에 하나씩 뽑아서 추가해 주어도 좋겠죠?
20190918 기준 오히려 안좋은 부품이 있어서 하나 제외시킵니다. ^^;
1. Ender-5 Bed Strain Relief 히팅베드 열선과 온도센서 케이블 고정용 브라켓!
https://www.thingiverse.com/thing:3443100
Ender-5 Bed Strain Relief by derandi3d
Strain relief for the Ender 5 heat bed wires. Mounted to the carriage using M4x12 or M3x12 + nut. 23.2.2019 Version 2 To avoid too much bending the wires if you level up and down higher than normal, i made some changes: 5mm more distance from bed. Larger r
www.thingiverse.com
이건 1순위입니다. 이 부위 납땜 떨어져서 울쌍짖는 분 많이 봤습니다. 해놓고 보니 정말 안심이 되더군요 ^0^/
이건 나사산이 있어서 10mm M4 무두볼트 하나 있으면 됩니다. 프린터 구매시 들어있는 얇은 타이 하나랑요~
2. Ender 5 bed supports - Super Struts Remix
https://www.thingiverse.com/thing:3661405
Ender 5 bed supports - Super Struts Remix by BoothyBoothy
This is a remix of jumpshoutmedia`s excellent Super Struts support for the Creality Ender 5. This was already a brilliant thing but I tweaked a few details to make the installation a little easier. In this remix I have: 1.Included nut retention sockets to
www.thingiverse.com
원본도 좋아 보이는데... 이게 수정된것 같아서 이거로 뽑았습니다. 저는 풀림방지 너트랑 20mm M4 무두볼트 사용하였습니다.
3. Ender 5 Upper Leadscrew Bracket 20190918 기준 제외합니다. ㅠㅠ;
이게 완전한 수평을 이루지 않을경우 오히려 와블?을 만드는 원인인것 같습니다. 이부분은 테스트를 좀더 해보고 또 글 수정하겠습니다. ^^;
https://www.thingiverse.com/thing:3611210
Ender 5 Z-Axis Stabi with Bearing (Skatebearing) by MonkeyDudes
This is a Remix
www.thingiverse.com
저는 카페이 있는 거로 했습니다. 이게 꼭 필요할까 싶긴 한데 공중에 떠있는 리드스쿠류는 고정해 놓으니 안정감이 있네요....
4. Cable protection for Ender-5
https://www.thingiverse.com/thing:3354725
Cable protection for Ender-5 by lgaga
Cable protection
www.thingiverse.com
이건 조립하기전에 뽑아서 적용하면 좋습니다. ^^;
5. 애증의 팬덕트...
https://www.thingiverse.com/thing:2759439
다운받으면 파일이 엄청 많은데 그중에... "BULLSEYE_DUCT_9.27." 프린트 하시면 됩니다.
Petsfang Duct for CR10 MicroSwiss/Stock/E3Dv6/Volcano/TevoTornado /Tarantula Hot End/E3Dv6 CNC Mount & 5015 fan Bullseye by dpet
Print with 4+ walls with 50%+ infill. These are structural parts and need to be strong, especially the mounting points. 9.27.2018 I adjusted the duct to have a little thicker arms around the holes and changed the larger inlet so you won't need a calibrated
www.thingiverse.com
https://www.thingiverse.com/thing:3343314 위 팬덕트용 브라켓...
Ender-5 Base for the "Petsfang Bullseye Duct" by Pryies
I printed the Ender-3 Base for the Bullseye Duct, figuring they were similar, only to find out the Ender 5 uses a different hot end bracket. Made a new version to fit the new bracket in Fusion 360 to work with the "BULLSEYE_DUCT_9.27." file found here http
www.thingiverse.com
https://www.thingiverse.com/thing:3599153
BL TOUCH를 사용하신다면...
Ender 5 with Bullseye and BLTouch by thehoffau
I wanted the bullseye on my Ender 5. The base which this is a remix of worked well but I was unable to mount a BLTouch onto it. Remixed the BLTouch mount into the base so its no longer modular. Left side would hit the wheels on the carriage so had to fit i
www.thingiverse.com
아래사진은 팬 적용 미적용 비교사진 후덜덜... 하네요 ㅎㅎ;
불스아이... 팬 그대로 사용하고... 선도 그대로 사용하고 최고의 팬입니다.
그러나... 오토홈 조용하게 하는... 아래 6번 뽑아 적용시 방해를 해서... 팬을 벼르고 벼르던 것으로 교체...!!!
Hero Me Remix 2 with Robust Assembly & Extended Wire Management
팬도 3개 다 사서 업 했습니다. ^^;
https://www.thingiverse.com/thing:3744260
Hero Me Remix 2 with Robust Assembly & Extended Wire Management by BoothyBoothy
Update:17_07_19 Uploaded 5015 Ducts V2_3 RH & LH. Increased the size of the duct retaining flange to create a much firmer seat\fit. Update:16_07_19 Uploaded 5015 Ducts V2_2 RH & LH. Rotated fan to improve fan cable management and reduce size of part. Fract
www.thingiverse.com
원래는 아래거 프린트 하려고 하다가 실패하고... 위에거 프린트... ^^
https://www.thingiverse.com/thing:3571199
Minimalistic Ender 3 fan mount - REDESIGN by Psyche607
OLD VERSION NEW VERSION v 3.0 Link: https://www.thingiverse.com/thing:3646456 Changes that are made in comparsion to base source: Better alignment, All metal Hot-End (Swiss Hot-End) better compatibility/alignment, Thicken walls - no more warping, Cable man
www.thingiverse.com
6.
Silent Auto Home for Ender-5 이건 반듯이 뽑아서 적용하세요...
센서가 충격에 의해 망가지는 것도 방지하면서 엄청 조용해집니다. ^^;
https://www.thingiverse.com/make:675509
Silent Auto Home for Ender-5 by woodwaker
This is a really great mod for the Ender 5. I printed it and took me a while to get around installing it. I had a little difficulty in figuring out how it installed. I hope my pictures may help someone that could not see the way to install. One thing that
www.thingiverse.com
7.
스풀러 못박는 부위만 살짝 바꿔도 공간활용이 확~ 삽니다.
거기에 스플러... ^0^/
최고입니다.
Filler - The Customizable Filament Holder that fills your printer!
https://www.thingiverse.com/thing:3020026
Filler - The Customizable Filament Holder that fills your printer! by HugoHuge
This design solves all the basic necessities: Fits almost every object with a flat top surface and printer frame when customized Can easily hold the weight of 1+ kg spools Fits between other spools if necessary In addition to above criteria, I've optimized
www.thingiverse.com
단지... 너무 잘 돌아가도 탈... 이라는 점... ㅠㅠ;
'3D PRINTER > CREALITY ENDER-5' 카테고리의 다른 글
| 큐라에서 ENDER-5 설정하기 20190815 최종수정 (0) | 2019.07.07 |
|---|---|
| ENDER 5 영입 ^0^ (0) | 2019.07.06 |
댓글